AiM Racing Data

AiM CAN 7-Pin to CAN/RS232 Wiring Harness for Solo DL Moving your original AiM Solo DL from one car to another and need another harness for only power or both power and data input, this is your cable. If you are putting a Solo DL into an older vehicle and need a power supply cable, use this and use only the + and - wires and fold back the can inputs. This harness connects your SoloDL to your ECU via CAN or RS232 wiring. One end has a 7-pin 712 (screw-in) connector to fit the SoloDL, and the other has 6 non-terminated wires (CAN+, CAN-, RS232RX, RS232TX, Power, and Ground). Does not fit the new AiM Solo2 DL. AiM CAN 7-Pin to CAN/RS232 Wiring Harness for Solo DL Details: Manufacturer: AiM Manufacturer part number: V02569080 Manufacturer alternate part number: MC-569 Fits Solo DL: Yes Fits Solo 2 DL: No Fits Solo Base Model: No Fits Solo 2 Base Model: No Length: 2 meters Pins on AiM Solo DL Side: 7 Pin Thread on connector Vehicle Chassis Ends: 6 Non terminated wires Vehicle Chassis Ends Break Out: CAN+, CAN-, RS232RX, RS232TX, Power, and Ground (and one unused) Note: Not compatible with the original SmartyCam (gray unit with the viewing screen on top) or the later SmartyCam HD "Rev 1". The version 1 can be identified by a 7/8" diameter lens with either a 67 or 87 degree field of view, and a viewfinder flush with the front of the housing. Later SmartyCam HD Rev 2 had a larger 1 3/8" OD lens marked as 60 or 120 degree field of view and a cover over the front viewfinder held on by 8 screws. 1 - CAN+ (white)2 – GND (black)3 – 12v (red)4 - CAN- (blue)5 – K-Line (blue or orange)6 - N/A

AiM CAN 7-Pin to OBD-II (K-Line Connector) Cable for Solo DL AiM Solo DL to OBD-II Port Connection Cable On Your Car For Easy Addition of RPM and other vehicle data. One end has the K-Line (OBD-2) plug to fit the diagnostic port, and the other end has a 7-pin 712 (screw-in) connector for the Solo DL. OBD-II is also known as K-Line This is the same cable supplied with the original AiM Solo DL for OBD-II. Does not fit the new Solo2 DL. AiM CAN 7-Pin to OBD-II (K-Line Connector) Cable for Solo DL Details: Manufacturer: AiM Manufacturer part number: V02569010 AiM Alternate part number: MC-568 End 1: AiM 7 Pin 712 (thread on) End 2: OBD-2 (K-Line) Fits AiM Solo: No Fits AiM Solo DL: Yes Fits AiM Solo 2: No Fits AiM Solo2 DL: No Note: Not compatible with the original SmartyCam (gray unit with the viewing screen on top) or the later SmartyCam HD "Rev 1". The version 1 can be identified by a 7/8" diameter lens with either a 67 or 87 degree field of view, and a viewfinder flush with the front of the housing. Later SmartyCam HD Rev 2 had a larger 1 3/8" OD lens marked as 60 or 120 degree field of view and a cover over the front viewfinder held on by 8 screws.

AiM Solo 2 DL RPM and Power Wiring Harness The AiM V02589020, called the AiM Solo 2 DL RPM Input Wire, is used to connect your AiM Solo 2 DL to an older generation (non-ECU) vehicle. On the bottom right of your Solo 2 DL there is an 8 pin connector that you can connect to the low voltage side of your coil. The peak can be anywhere from 150 to 400 V or from a square wave with a peak of 5 to 50 V. If you have a vehicle with no ECU or OBD-2 Port or a MSD ignition box, this is your easiest way to log RPM. By connecting the positive and negative wires, your Solo 2 DL unit will automatically top off the internal battery and power all down line appliances, such as SmartyCams and other powered devices. AiM Solo 2 DL RPM Input Wire Details: Manufacturer: AIM Manufacturer part number: V02589020 End 1: Male 712 8 Pin Screw-in End 2: Flying lead (open wires) 12 V Positive , Negative, and RPM input Length: 2 Meters AiM Solo 2 DL RPM Input Wire Uses: Solo 2 DL to older external coil engines Solo 2 DL to RPM tach lead Solo 2 DL to MSD ignition box

AiM Trackday Kit Short Cable for SmartyCam 3 The AiM Trackday kit mount offers a neat solution for connecting your Solo 2 DL & SmartyCam 3 without dealing with the 2 meter cable normally included with the Smartycam. If you need the mount for your Solo 2 and SmartyCam 3, that can be found here! AiM Trackday Kit Short Cable for SmartyCam 3 & Solo 2 DL Details: Manufacturer: AiM Technologies Manufacturer Part Number: V02554910 Cable Length: Approx 7" 712 5-pin male to 712 5-pin male

AiM 5 Pin 712 -712 CAN / GPS Extension Cable AiM GPS & CAN extension cable with the 5 pin male going to a 5 pin female connector. The 712 5 pin has 5 pins and a chrome threaded barrel (screw-in) connection. These extension cables are used to lengthen any CAN cable to provide a perfect installation. We use the AiM 712-715 patch cable to lengthen an AiM GPS08 antenna, Data Hub or any other CAN item. These are male on one side and female on the other side, so connecting them is series is allowed. This cable will fit between a SmartyCam GP process and lens, but will not work. You need the AiM SmartyCam GP LVDS Cable for this. AiM 5 Pin 712 -712 CAN / GPS Extension Cable Details: Manufacturer: AIM Manufacturer part number Patch cable, 1m 712 5-pin/m to 712, 5-pin/f CAN: V02552700 Manufacturer part number Patch cable, 2m 712 5-pin/m to 712, 5-pin/f CAN: V02552720 Manufacturer part number Patch cable, 3m 712 5-pin/m to 712, 5-pin/f CAN: V02552730 Manufacturer part number Patch cable, 4m 712 5-pin/m to 712, 5-pin/f CAN: V02552740 End 1: Male 712 5 Pin Screw-in End 2: Female 712 5 Pin Screw-in AiM 5 Pin 712 -712 CAN / GPS Extension Cable Common Uses CAN Extension GPS Extension Data Hub Extension AiM 5 Pin 712 -712 CAN / GPS Extension Cable Lengths Available: 1 Meter (39") 2 Meter (78") 3 Meter (118") 4 Meter (156")

AiM Shift Light Module Patch Cable 1 Meter The AiM Shift Light Module has a female 712 5 pin connection on the module. To connect it to your AiM dash you will need an extension cable like the AiM V02554810 that has both male 712 5 pin male going to a 712 5 pin male connector. The 712 5 pin has 5 pins and a chrome threaded barrel (screw-in) connection. This AiM SLM (Shift Light Module) extension cables are used to connect your AiM SLM to your Data hub or dash expansion harness. AiM Shift Light Module Patch Cable 1 Meter Details: Manufacturer: AIM Manufacturer part number: V02554810 Patch cable, 1.5m 712 5-pin/m to 712, 5-pin/m End 1: Male 712 5 Pin Screw-in End 2: Male 712 5 Pin Screw-in

MyChron5 & 4 2T Y-Cable, CHT & EGT One of the most common uses of this cable is to use an under the spark plug cylinder head temperature (CHT) and an exhaust gas temperature (EGT). We use this on a Yamaha KT100, LO206, Animal or clone motor to record both CHT & EGT as our two temperature inputs. MyChron 5 & 4 2T Y-Cable, CHT & EGT Details: Manufacturer: AiM Manufacturer part number: V02557070 Alternate part number: MC-016 Kart Only: Yes MyChron5 2T: Yes MyChron4 2T: Yes Cable End 1: 7-pin 712 screw on (dash) Cable End 2: K-Type (2 pin flat yellow female - egt or CHT) Cable End 3: K-Type (2 pin flat yellow female - egt or CHT) Length of 712 7 pin male to cunction: 54.5" Lengh of junction to flat yellow egt or CHT coupler: 2.5" AiM Y-Cable is designed for the MyChron5 2T kart dash. This Y-Cable is designed for the MyChron5 2T and MyChron4 2T kart dash. It has a 712 7-pin male connector for the dash, and two K-type (2-pin flat yellow) female connectors to accept K-type thermocouples.

AiM Sports SmartyCam to Solo/Dash Cable NOTE: Cables typically take 3 to 5 business days to ship. Have more than one vehicle with a dash or Solo 2 DL? Want to make swapping your SmartyCam between vehicles easier? Grab this extra 4M cable for your second car, route the cable as needed and leave it in place to power your SmartyCam when you drive that car. This cable takes the headache out of the process for people with more than one vehicle but only one SmartyCam. Four meters (13 feet) in length.

AiM Sports 712 to 719 Four-Pin Patch Cables NOTE: Cables typically take 3 to 5 business days to ship. Add the appropriate AiM Sports 712 to 719 4-Pin Extension Cables to your AiM data set-up to retrieve exactly the information you need to maximize your data acquisition and take your racing to the next level! The AiM Sports 712 to 719 4-Pin Patch Cables have a female 4-pin 719 (plastic) connector at one end and a male 4-pin 712 (threaded) connector at the other to connect most analog automotive sensors to the MyChron3, XG-Log Auto Dash, AiM EVO4, or AiM EVO4s Data Logger. Available in 0.5 thru 4 Meter lengths. CONNECTS TO: MyChron3 Data Hub XG-Log Auto Dash EVO4 Logger EVO4s Logger PART NUMBERS: V02PCB05BTXG cable length: 0.5m (1.6 ft) V02PCB10BTXG cable length: 1 meter (3.3 ft) V02PCB15BTXG cable length: 1.5 meter (4.9 ft) V02PCB20BTXG cable length: 2 meters (6.6 ft) V02PCB25BTXG cable length: 2.5 meters (8.2 ft) V02PCB30BTXG cable length: 3 meters (9.8 ft) V02PCB35BTXG cable length: 3.5 meters (11.5 ft) V02PCB40BTXG cable length: 4 meters (13.1 ft)

AiM Sports 5-pin 712 To 712 CAN Patch Cable These cables each have a female 5-pin 712 (screw-in) connector on one end and a male 5-pin 712 connector on the other. The 5-pin 712 connector is used on all AiM dash and data logger CAN inputs. These cables will extend the reach of CAN hubs and other accessories. Part numbers: V022552700 cable length: 1 Meter V022552720 cable length: 2 Meters V022552730 cable length: 3 Meters V022552740 cable length: 4 Meters

Thermocouple extension cable with 712 3-pin male end to K-style female end. 5.00 ft. cable length.

AiM Sports CHT Thermocouple Sensors Add the appropriate AiM Sports Cylinder Head Temperature sensor to your AiM data set-up to retrieve exactly the information you need to maximize your data acquisition and take your racing to the next level! AiM devices can measure the cylinder head temperature using a sensor – thermocouple – placed between the spark plug and the cylinder head. All AiM thermocouples are K-type sensors. Install this CHT thermocouple to monitor temperatures ranging from 0º to 572ºF (up to 300ºC). Choose your sensor diameter to fit either 14mm, 12mm, or 10mm spark plugs. The sensing ring is 0.7 inch (18mm) thick. TEMPERATURE SENSOR CHOICES This thermocouple is available to fit three different spark plug diameters, various cable lengths, and two different end connectors as follows: CHT14B: 14mm diam, 1.5m cable length, Binder 712 3-pin male   CHT14M: 14mm diam, 0.4m cable length, Mignon 2-pin male CHT12B: 12mm diam, 1.4m cable length, Binder 712 3-pin male CHT12M: 12mm diam, 0.4m cable length, Mignon 2-pin male CHT10B: 10mm diam, 1.4m cable length, Binder 712 3-pin male CHT10M: 10mm diam, 0.4m cable length, Mignon 2-pin male

AiM SmartyCam GP Replacement Lens 84º AiM SmartyCam GP bullet camera replacement lens with an 84º field of view. The 84º lens is usually used in Formula cars, karting & bike applications as it allows a wider left to right viewing area compared to the 67º lens. This kit includes a brand new genuine AiM 84º lens and the special weather- and harmonic-resistant O-ring. AiM SMARTYCAM GP REPLACMENT 84º LENS DETAILS: Manufacturer: AiM Manufacturer part no: X96KVBGPHD Field of view: 84º O-ring included: Yes

AiM SmartyCam GP HD Replacement Lens 67 AiM AiM SmartyCam GP HD Replacement Lens with the 67 field of view. The 67 is usually used in almost all production cars, GT and all sports cars. This kit includes a new Genuine AiM 67 lens and the special weather and harmonic resistant o-ring. AiM SmartyCam GP HD Replacement Lens 67 Details: Manufacturer: AiM Manufacturer part number: X96KVBGPHD6 Degree of field of view: 67 O-ring included: Yes

RAM Windshield Suction Mount Among the great advantages to the AiM Solo family of GPS lap timers is that, unlike other timers, you don't have to connect any wires to use it. That makes it ideal for use in daily-driven track-day cars (or for moving from one car to another). The RAM windshield mount lets you to mount your AiM Solo2 or Solo2 DL (and older Solo versions) to your windshield quickly and securely. Installation is as easy as pushing a lever; removal is as easy as lifting the lever. Two pivoting ball joints allow a wide range of adjustment. Two 6mm screw holes match the holes in the standard mounting plate included with your AiM Solo2 or Solo2 DL. There's no better, more convenient way to mount your AiM Solo2 / Solo2 DL.